Tensile Strength, Ultimate:565 MPa 81900 psi:Tensile Strength, Yield:310 MPa:45000 psi:Elongation at Break (in 50 mm) 16.0 %:16.0 %:Reduction of Area:40.0 %:40.0 %:Modulus of Elasticity (Typical for steel) 200 GPa:29000 ksi:Bulk Modulus (Typical for steel) 140 GPa:20300 ksi:Poissons Ratio (Typical For Steel) 0.290:0.290:Shear Modulus (Typical for steel) 80 GPa:11600 ksi
Non-alloy quality steel Chemical composition of steel C45 (1.0503), Standards of steel C45 (1.0503) Mechanical Properties of steel C45 (1.0503) Equivalent grades of steel C45 (1.0503) steel C45 (1.0503) Tensile Strength, Elongation, Proof strength , Hardness C45 Round Bar AISI 1045 DIN 1.1191 - Otai Special SteelSteel C45 Round Bar is an unalloyed medium carbon steel, which is also a general carbon engineering steel. C45 is a medium strength steel with good machinability and excellent tensile properties. C45 round steel is generally supplied in the black hot rolled or occasionally in the normalised condition, with a typical tensile strength range 570 -
Alloy structural steel is provided with higher yield strength, tensile strength, endurance strength, yield ratio (about 0.85 generally ) enough plasticity and toughness. The concentration of alloy element of this kind of steel is quite high, mainly are corrosion resistant steel, heat resistant steel, wear resistant steel, and other special C45E / 1.1191 - SteelNumber - Chemical composition Non-alloy quality special steel Chemical composition of steel C45E (1.1191), Standards of steel C45E (1.1191) Mechanical Properties of steel C45E (1.1191) Equivalent grades of steel C45E (1.1191) steel C45E (1.1191) Tensile Strength, Elongation, Proof strength , Hardness
Steel GradesCk45 Chemical information,Mechanical properties Physical properties, Mechanical properties, Heat treatment, and Micro structure C Si Mn P S Cr Ni 0.42-0.5 0 0.40 0.50-0.8 0 0.030 0.035 Mo Al Cu Nb Ti V Ce N Co Pb B Other Cr+Ni+Mo 0.63 Ck45 Physical Properties Tensile strength 115-234 b/MPa Yield Strength 23 GALVANIZED STEEL Grade Data Sheet - CascadiaSteel base Guaranteed Typical Range Guaranteed Maximum Percent Longitudinal tensile Carbon (C) 0.20 Yield strength, minimum ksi 33 33-51 Phosphorus (P) 0.10 Tensile strength, minimum ksi 45 45-64 Manganese (Mn) 1.35 Elongation in 2 inch, minimum % 20 20-37 Sulfur (S) 0.04
GB/T 699-1999 Grade 45 is a quality carbon structural steel that is widely used in mechanical manufacturing applications and high-strength moving parts. Show Medium Carbon Steel materials with Tensile strength of 600 MPa at 20 °C. Yield strength. YS. 355 MPa at 20 °C. Show Medium Carbon Steel materials with Yield strength of 355 MPa at 20 GB/T 45 - Medium Carbon Steel - MatmatchGB/T 699-1999 Grade 45 is a quality carbon structural steel that is widely used in mechanical manufacturing applications and high-strength moving parts. Show Medium Carbon Steel materials with Tensile strength of 600 MPa at 20 °C. Yield strength. YS. 355 MPa at 20 °C. Show Medium Carbon Steel materials with Yield strength of 355 MPa at 20
High-Strength 1045 Carbon Steel Rods and Discs Stronger than low-carbon steel with equally good machinability, 1045 carbon steel is widely used for bolts, studs, and shafts. Ground rods are decarb-free for a uniform surface that will consistently accept heat treating. Grade 1045 Steel McMaster-CarrHigh-Strength 1045 Carbon Steel Rods and Discs Stronger than low-carbon steel with equally good machinability, 1045 carbon steel is widely used for bolts, studs, and shafts. Ground rods are decarb-free for a uniform surface that will consistently accept heat treating.
Metal Mechanical Properties Chart:Shear Strength, Tensile Strength, Yield Strength Metals & Materials / 5 minutes of reading Recently weve been getting a lot of inquiries from readers about mechanical property tables for various metals, such as the shear strength, tensile strength, yield strength and elongation of steel, etc. Spring steel suppliers & stockist grades:EN42,43,45,47 WHAT IS EN 45 SPRING STEEL? EN 45 is a Silicon Manganese Steel. It is also Supplied in Rolled Condition. This Steel is Suitable for Oil Hardening and also Tempering. THE COMPOSITION OF EN 45 STEEL IS:-C. 0.55%. Si. 1.75%. Mn. 0.75%. S. 0.05%. P. 0.05%. WHAT IS EN 45 A SPRING STEEL? EN 45 is a Silicone Manganese Spring Steel.
Yield Strength, Modulus of Elasticity, Ultimate Strength of Selected Materials A straight line is drawn through Point (D) at the same slope as the initial portion of the stress-strain curve. The point of intersection of the new line and the stressstrain curve is projected to the stress axis. Yield Strength Testing - Yield strength Ultimate strength For the low alloy steel, the yield strength is usually about 75-90% of the tensile strength. The comparable figure for a mild steel is about 65-75%. For the annealed austenitic stainless steel, its yield strength is a very low proportion of the tensile strength, typically only 40-45%, but only a few % of cold work will increase the yield by 200
Yield strength (MPa) Steel (Steel number) MPa, Diamter (d), Thickness (t) in mm:Conditions:C45 (1.0503) 490:d 16 t 8:Quenched and tempered (for the ruling section) 430:16 < d 40 8 < t 20:370:40 < d 100 20 < t 60:340:d, t 16:Normalized (for products) 305:16 <d, t
Please Click here