Haihong International Trade (HK) CO., Limited. Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. 0Cr17Ni4Cu4Nb can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc. TEL:+86-816- FAX:+86-816-2
17-4 stainless is an age-hardening martensitic stainless combining high strength with the corrosion resistance of stainless steel. Hardening is achieved by a short-time, simple low-temperature treatment. Unlike conventional martensitic stainless steels, such as type 410, 17-4 is quite weldable. 17-4 PH Stainless Steel McMaster-CarrHigh-Strength 17-4 PH Stainless Steel. Hardened for improved strength and wear resistance, these rods are precision ground to a strict diameter tolerance. Use them for turning applications in your lathe. Hardened Tight-Tolerance High-Strength 17-4 PH Stainless Steel with Certification.
17-4 PH stainless steel is capable of attaining a wide range of strength and toughness properties depending on the precipitation or aging temperature used in hardening. Its high strength, good corrosion resistance and toughness in both base metals and welds gives designers opportunities to add reliability to their products while simplifying fabrication and often reducing costs. 17-4 Stainless Steel Bar - 17-4PH CRES Condition A Round 17-4 Stainless Steel Bar 17-4 ph Stainless Steel Bar 17-4 is a chromium-nickel-copper precipitation hardening stainless steel used for applications requiring high strength and moderate level of
17-4PH(UNS S17400) AMS 5604 Tube / Pipe is a martensitic, chromium-nickel-copper precipitation-hardening stainless steel. 17-4 PH stainless steel is capable of attaining a wide range of strength and toughness properties depending on the precipitation or aging temperature used in hardening.Its valuable combination of high strength, good corrosion resistance and toughness in both base metals and ASTM 17-4PH - Longhai Special Steel17-4PH material is ASTM SAE AMS 5342E (2006) Steel, Corrosion-Resistant, Investment Castings 16Cr - 4.1Ni - 0.28Cb (Nb) - 3.2Cu Homogenization, Solution, and Precipitation Heat Treated (H1100) 130 ksi (896 MPa) Tensile Strength (17-4) ASTM SAE AMS 5343E (2006) Steel, Corrosion-Resistant, Investment Castings 16Cr - 4.1Ni - 0.28Cb (Nb) - 3.2Cu Homogenization, Solution, and Precipitation
Stainless Steel 17-4 Product Guide Stainless Steel Tolerance Table. Stainless Steel Round Bar/Rod 17-4 PH Annealed Cold Finish is normally used in natural gas/petroleum/oil, aerospace, thermal, and chemical applications. 17-4 PH stainless has high tensile strength and hardness and excellent corrosion resistance up to high temperatures. 17-4 round bar/rod stock is available in full size and China Stainless Steel Materials Quality Supplier Stainless Steel Round Bar / Rod. Standard:ASTM, JIS, DIN, EU Grade:304(L), 316(L), 17-4PH Size:Diameter:2mm - 600mm Introduction:Stainless steel round bars are categorized as both long products and bar materials. SS round bar is long stainless steel product Learn More
Features:17-4PH is a chromium-nickel-copper precipitation hardening martensitic stainless steel that combines oxidation and corrosion resistance comparable to 304 in most environments with high strength and hardness. It is the most widely used of all the precipitation hardening stainless steels, and is more cost effective than many high nickel non-ferrous alloys in someApplications. 17-4PH STAINLESS STEEL PRODUCTS - Nextgen Steel & AlloysStainless Steel 17-4PH Density, Stainless Steel 304 Nuts And Bolts, Stainless Steel Pipe, Stainless Steel Rod, Stainless Steel 304 Pipe Suppliers In Mumbai, Stainless Steel 316 Pipe Suppliers In Mumbai, Stainless Steel 316 Plates Suppliers In Mumbai, Stainless Steel 15-5PH Plates Suppliers In Mumbai, 13-8mo Round bars supplier in Mumbai, India.
17-4 (Type 630) Stainless Steel Round Typical Applications 17-4 is used where high strength and good corrosion resistance are required, as well as for applications requiring high fatigue strength, good resistance to galling, seizing and stress corrosion. Stainless Alloy 17-4 PH® 17-4 PH® Alloy Steel 17-4 PH®17-4Ph offers high strength and hardness along with excellent corrosion resistance.17-4 Ph has been used for a variety of applications including oil field valve parts, chemical process equipment, aircraft fittings, fasteners, pump shafts, nuclear reactor components, gears, paper mill equipment, missile fittings, and jet engine parts.
Product Data Sheet Stainless Steel:Alloy17-4PH UNS-S17400. Also known as AISI Grade 630. Stainless Steel Alloy Grade 17-4PH is a precipitation hardening stainless steel which has extremely high strength and hardness, combined with good ductility and toughness. It has excellent corrosion resistance, approaching that of stainless steel grade Stainless Steel Round Bar 17-4 PH 2.5 (A) (Click & Buy)Please enter a valid decimal number between 1.000 and 72.000 inches. Examples:1 , 7 , 20 , 25.3 , 32.75 , 35.625 ALL CUSTOM SIZE ORDERS ARE SUBJECT
17-4PH stainless is a kind of precipitation hardened martensitic stainless under American standard. It has lower carbon component, while it has higher Ni & Cr chemicals. And moreover Cu & Nb alloy chemicals have been added into 17-4PH, all these alloy components will help to harden 17-4PH material while it is done heat treatment. 17-4PH, 17 is China AISI 630 17-4pH Stainless Steel Seamless Pipe China AISI 630 17-4pH Stainless Steel Seamless Pipe, Find details about China SUS 630, 0Cr17Ni4Cu4Nb from AISI 630 17-4pH Stainless Steel Seamless Pipe -
Please Click here